PLUMBING FOR BEGINNERS: WHAT YOU NEED FOR INSTALLING A BATHTUB

Plumbing for Beginners: What You Need for Installing a Bathtub

Plumbing for Beginners: What You Need for Installing a Bathtub

Blog Article

Explore Now

We've discovered this post relating to How to Install a Bathtub below on the web and felt it made good sense to share it with you here.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bath tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is easily obtainable, the task can relocate rapidly; if you need to open up a wall to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Make sure you have actually certified on your own for the task as well as fit trying it. Rather than hiring a service provider to take control of a halfway-completed job, it is much better to consider utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This article will help you set up a new bath tub in your restroom if you have actually already gotten a brand-new tub and don't require to change the setup of your previous supply of water pipes.
Your tools and also product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited access that is typically the case.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing substance.
    Prior to moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the current supply pipelines.
    If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet and the sink. Protect the faucet in place with the maker provided backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind should be linked to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Setting up the Bathtub


    Using the two wooden boards under its feet, position the bath tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 small points.
    The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bath tub until the spirit level checks out degree.
    To set up faucets, fit all-time low of the furthest adaptable faucet port to the ideal supply pipe by making a compression join; then do the same for the other faucet.
    Switch on the water supply and also inspect all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the bathtub as well as additionally examine the overflow outlet and also the regular outlet for leakages.
    Finally, fix the bath paneling as described in the producer's user's manual. Tiling and sealing around the bath tub needs to wait up until the bath tub has been used at least once as this will resolve it into its final position.

    Planning for the Installment


    Firstly, the sustaining framework supplied with the bath should be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to stop strain on the bathtub.
    Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washing machines.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last position.

    Tiling Around the Bathtub


    In the location where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, causing difficulties with wetness as well as possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before sealing, to permit the activity experienced when the tub is in use. The sealant can fracture rather very early if you do not take into consideration this motion before securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    As a keen person who reads about How to Install a Bathtub Yourself, I thought sharing that piece of content was really useful. Sharing is good. One never knows, you may just be doing someone a favor. Thanks a lot for taking the time to read it.


    We're on standby!

    Report this page